last chance saloon!

README.md

@@ -86,6 +86,25 @@ The installation script automates the following steps:
 
 After installation is complete, the script will provide instructions to start the service manually or to run the application in its interactive terminal mode.
 
+---
+
+## 🔄 Updating
+
+If you installed TimeTurner by cloning the repository with `git`, you can use the `update.sh` script to easily update to the latest version.
+
+**Note**: This script will not work if you used the `curl` one-line command for installation, as that method does not create a Git repository.
+
+To run the update script, navigate to the `NTP-Timeturner-main` directory and run:
+```bash
+chmod +x update.sh && ./update.sh
+```
+
+The update script automates the following:
+1.  Pulls the latest code from the `main` branch on GitHub.
+2.  Rebuilds the application binary.
+3.  Copies the new binary to `/opt/timeturner/`.
+4.  Restarts the `timeturner` service to apply the changes.
+
 ---
 ## 🕰️ Chrony NTP 
 ```bash

setup.sh

@@ -3,6 +3,43 @@ set -e
 
 echo "--- TimeTurner Setup ---"
 
+# Check if TimeTurner is already installed.
+INSTALL_DIR="/opt/timeturner"
+if [ -f "${INSTALL_DIR}/timeturner" ]; then
+    echo "✅ TimeTurner is already installed."
+    # Ask the user what to do
+    read -p "Do you want to (U)pdate, (R)einstall, or (A)bort? [U/r/a] " choice
+    case "$choice" in
+        r|R )
+            echo "Proceeding with full re-installation..."
+            # Stop the service to allow overwriting the binary, ignore errors if not running
+            echo "Stopping existing TimeTurner service..."
+            sudo systemctl stop timeturner.service || true
+            # The script will continue to the installation steps below.
+            ;;
+        a|A )
+            echo "Aborting setup."
+            exit 0
+            ;;
+        * ) # Default to Update
+            echo "Attempting to run the update script..."
+            # Ensure we are in a git repository and the update script exists
+            if [ -d ".git" ] && [ -f "update.sh" ]; then
+                chmod +x update.sh
+                ./update.sh
+                # Exit cleanly after the update
+                exit 0
+            else
+                echo "⚠️  Could not find 'update.sh' or not in a git repository."
+                echo "Please re-clone the repository to get the update script, or remove the existing installation to run setup again:"
+                echo "  sudo rm -rf ${INSTALL_DIR}"
+                exit 1
+            fi
+            ;;
+    esac
+fi
+
+
 # Determine package manager
 PKG_MANAGER=""
 if command -v apt &> /dev/null; then
@@ -227,8 +264,9 @@ if [ "$PKG_MANAGER" == "apt" ]; then
     echo "✅ nodogsplash installed successfully."
 
     # Disable the standalone hostapd service to let NetworkManager manage it.
-    sudo systemctl disable hostapd
+    # We are now using the classic hostapd service, so unmask it.
-    sudo systemctl mask hostapd
+    sudo systemctl unmask hostapd
+    sudo systemctl enable hostapd
     sudo systemctl enable nodogsplash
 else
     echo "This script is designed for Debian-based systems like Raspberry Pi OS."
@@ -240,40 +278,71 @@ fi
 sudo systemctl stop hostapd || true
 sudo systemctl stop dnsmasq || true
 
-# Ensure NetworkManager is managing wlan0 by removing any conflicting configurations.
+# --- Configure networking for AP mode ---
-# This is the critical fix for the "No suitable device" error.
+
-echo "Ensuring NetworkManager is managing wlan0..."
+# Set the WiFi country code to prevent radio issues. This is a critical step.
-sudo rm -f /etc/NetworkManager/conf.d/99-unmanaged-wlan0.conf
+echo "Setting WiFi Country Code to US..."
+sudo raspi-config nonint do_wifi_country US
+
+# Tell NetworkManager to ignore wlan0 completely to prevent conflicts.
+echo "Configuring NetworkManager to ignore wlan0..."
+sudo tee /etc/NetworkManager/conf.d/99-unmanaged-wlan0.conf > /dev/null <<EOF
+[keyfile]
+unmanaged-devices=interface-name:wlan0
+EOF
+# Also remove the DNS disabling config as it's no longer relevant for this method
+sudo rm -f /etc/NetworkManager/conf.d/99-disable-dns.conf
 sudo systemctl reload NetworkManager
 
-# Configure static IP for wlan0 using NetworkManager (nmcli)
+# Configure a static IP for wlan0 using dhcpcd.
-echo "Configuring static IP for wlan0 using NetworkManager..."
+echo "Configuring static IP for wlan0 via dhcpcd..."
+# Ensure dhcpcd is installed
+sudo apt install -y dhcpcd5
 
-# Define the connection name
+# First, remove any existing configurations for wlan0 to prevent conflicts.
-CON_NAME="TimeTurner-AP"
+# This is a more robust way to ensure our settings are applied.
+sudo sed -i '/^interface wlan0/,/^\s*$/d' /etc/dhcpcd.conf
 
-# If a connection with this name already exists, delete it to ensure a clean slate.
+# Now, add our static IP config to the end of the file.
-if nmcli c show --active | grep -q "$CON_NAME"; then
+sudo tee -a /etc/dhcpcd.conf > /dev/null <<EOF
-    sudo nmcli c down "$CON_NAME" || true
-fi
-if nmcli c show | grep -q "$CON_NAME"; then
-    echo "Deleting existing '$CON_NAME' connection profile..."
-    sudo nmcli c delete "$CON_NAME" || true
-fi
 
-# Create a new connection profile for the Access Point with a static IP.
+# Static IP configuration for Hachi Time AP
-echo "Creating new '$CON_NAME' connection profile..."
+interface wlan0
-sudo nmcli c add type wifi ifname wlan0 con-name "$CON_NAME" autoconnect yes ssid "TimeTurner"
+    static ip_address=10.0.252.1/24
-sudo nmcli c modify "$CON_NAME" 802-11-wireless.mode ap 802-11-wireless.band bg
+    nohook wpa_supplicant
-sudo nmcli c modify "$CON_NAME" 802-11-wireless-security.key-mgmt wpa-psk
+EOF
-sudo nmcli c modify "$CON_NAME" 802-11-wireless-security.psk "harry-ron-hermione"
+
-sudo nmcli c modify "$CON_NAME" ipv4.method manual ipv4.addresses 10.0.252.1/24
+# Configure hostapd for the Access Point
+echo "Configuring hostapd..."
+sudo tee /etc/hostapd/hostapd.conf > /dev/null <<EOF
+interface=wlan0
+driver=nl80211
+ssid=Fetch-Hachi
+hw_mode=g
+channel=7
+ieee80211n=1
+wmm_enabled=1
+macaddr_acl=0
+auth_algs=1
+ignore_broadcast_ssid=0
+EOF
+# Point the hostapd service to the new config file.
+sudo sed -i 's|#DAEMON_CONF=""|DAEMON_CONF="/etc/hostapd/hostapd.conf"|' /etc/default/hostapd
 
 # Configure dnsmasq for DHCP
 echo "Configuring dnsmasq..."
 sudo tee /etc/dnsmasq.conf > /dev/null <<EOF
+# Listen only on this interface
 interface=wlan0
+# Don't bind to all interfaces, only the one specified above
+bind-interfaces
+# Set the IP range for DHCP clients
 dhcp-range=10.0.252.10,10.0.252.50,255.255.255.0,24h
+# Provide a gateway address
+dhcp-option=option:router,10.0.252.1
+# Provide a DNS server address
+dhcp-option=option:dns-server,10.0.252.1
+# For captive portal, resolve all DNS queries to the AP itself
 address=/#/10.0.252.1
 EOF
 
@@ -285,17 +354,30 @@ GatewayAddress 10.0.252.1
 MaxClients 250
 AuthIdleTimeout 480
 FirewallRuleSet preauthenticated-users {
-    FirewallRule allow tcp port 80
+    # Allow DHCP for clients to get an IP address
+    FirewallRule allow udp port 67
+    FirewallRule allow udp port 68
+    # Allow DNS for captive portal detection
     FirewallRule allow tcp port 53
     FirewallRule allow udp port 53
+    # Allow HTTP for the captive portal redirect
+    FirewallRule allow tcp port 80
 }
 RedirectURL http://10.0.252.1/static/index.html
 EOF
 
 # Restart services in the correct order and add delays to prevent race conditions
 echo "Restarting services..."
-# Bring up the new AP connection using nmcli
+
-sudo nmcli c up "$CON_NAME"
+# Stop and disable systemd-resolved to prevent any DNS/DHCP conflicts
+echo "Disabling systemd-resolved to ensure dnsmasq has full control..."
+sudo systemctl stop systemd-resolved || true
+sudo systemctl disable systemd-resolved || true
+
+# Restart dhcpcd to apply the static IP
+sudo systemctl restart dhcpcd
+# Restart hostapd to create the access point
+sudo systemctl restart hostapd
 
 # Wait for the interface to come up and get the IP address
 echo "Waiting for wlan0 to be configured..."
@@ -314,7 +396,19 @@ done
 # Check for the IP address before starting nodogsplash
 if [ "$IP_CHECK" == "10.0.252.1" ]; then
     echo "✅ wlan0 configured with IP $IP_CHECK."
-    sudo systemctl restart dnsmasq
+    
+    # Add a small delay to ensure the interface is fully ready for dnsmasq
+    sleep 2 
+
+    echo "Attempting to start dnsmasq service..."
+    if ! sudo systemctl restart dnsmasq; then
+        echo "❌ dnsmasq service failed to start. Displaying logs..."
+        sleep 2
+        sudo journalctl -u dnsmasq.service --no-pager -n 50
+        exit 1
+    fi
+    echo "✅ dnsmasq service started successfully."
+
     if command -v nodogsplash &> /dev/null; then
         echo "Attempting to start nodogsplash service..."
         if ! sudo systemctl restart nodogsplash; then
@@ -332,11 +426,11 @@ if [ "$IP_CHECK" == "10.0.252.1" ]; then
     fi
 else
     echo "❌ Error: wlan0 failed to get the static IP 10.0.252.1. Found: '$IP_CHECK'."
-    echo "Please check 'sudo nmcli c show \"$CON_NAME\"' and 'ip addr show wlan0'."
+    echo "Please check 'sudo systemctl status hostapd' and 'sudo systemctl status dhcpcd'."
     exit 1
 fi
 
-echo "✅ WiFi hotspot and captive portal configured. SSID: TimeTurner, IP: 10.0.252.1"
+echo "✅ WiFi hotspot and captive portal configured. SSID: Fetch-Hachi, IP: 10.0.252.1"
 echo "Clients will be redirected to http://10.0.252.1/static/index.html"
 
 # 1. Build the release binary
@@ -389,7 +483,7 @@ if [[ "$(uname)" == "Linux" ]]; then
     echo "  sudo systemctl start timeturner.service"
     echo ""
     echo "To view live logs, run:"
-    echo "  journalctl -u tim_turner.service -f"
+    echo "  journalctl -u timeturner.service -f"
     echo ""
 fi
 echo "To run the interactive TUI instead, simply run from the project directory:"

update.sh

@@ -0,0 +1,28 @@
+#!/bin/bash
+set -e
+
+echo "--- TimeTurner Update Script ---"
+
+# 1. Fetch the latest changes from the git repository
+echo "🔄 Pulling latest changes from GitHub..."
+git pull origin main
+
+# 2. Rebuild the release binary
+echo "📦 Building release binary with Cargo..."
+cargo build --release
+
+# 3. Stop the currently running service to release the file lock
+echo "🛑 Stopping TimeTurner service..."
+sudo systemctl stop timeturner.service
+
+# 4. Copy the new binary to the installation directory
+echo "🚀 Deploying new binary..."
+sudo cp target/release/timeturner /opt/timeturner/timeturner
+
+# 5. Restart the service with the new binary
+echo "✅ Restarting TimeTurner service..."
+sudo systemctl restart timeturner.service
+
+echo ""
+echo "Update complete. To check the status of the service, run:"
+echo "  systemctl status timeturner.service"